Audio-Technica M2 Wireless In-Ear Monitor System
Related Products
- Description
- Specifications
- Reviews
Description
Product Description
The M2 Wireless In-Ear Monitor System is for those who do not want to worry about problems related with floor wedges. The Personal Mix Control in this monitor system allows the user to control two independent stage signals on the volume and the mix, through the easy-to-use controls on the M2R body-pack receiver. A choice of 100 selectable frequencies are provided in the wireless UHF M2T Stereo Transmitter and the two XLR ¼” combo input connectors it fits permit the user to connect line-level inputs. These systems are built to stand the harsh on-the-road life to deliver a clear natural sound not only for touring but also for installed-sound uses.
Product Features
- High-fidelity sound permits you to hear yourself better at a lower volume
- 100 selectable UHF channels
- Up to 10 simultaneous systems per frequency band
- Three receiver modes: Personal Mix, stereo, and mono
- Personal Mix Control for volume and mix control of two independent signals at the receiver
- 3.5 mm line-in jack connectors
- Level monitoring via LED indicators
- XLR loop output to connect signal to mixing console, additional IEM system or recording device
- Squelch button to eliminate static
- Pilot tone protection against RF interference
- Limiter for protection against sudden peaks
- Quick load and set up
- Reduces on-stage audio clutter for better overall mix & less feedback
- M2R Stereo Receivers may be used in any number on the same frequency
- Excellent isolation and full enhanced frequency on the earphones
- 3 sizes of rubber ear tips for personal fitting
- Aux input gives a connecting point for line-level input, ambience mic, click-track or another microphone
Specifications
Product Specification
| OVERALL | ||
| Operating Frequencies | Band E; 790.000 to 822.000 MHz-100 frequencies, Band F; 832.000 to 865.000 MHz-100 frequencies, Band L; 575.000 to 608.000 MHz-100 frequencies, Band M: 614.000 to 647.000 MHz-100 frequencies | |
| Minimum Frequency Step | 25 kHz | |
| Modulation Mode | FM stereo | |
| Maximum Deviation | ±40 kHz | |
| Dynamic Range | 90 dB (typical), A-weighted | |
| Total Harmonic Distortion | <1% at (1 kHz, ±20 kHz Deviation) | |
| Operating Range | 100 m (300'), typical | |
| Operating Temperature Range | -5° C (23° F) to +50° C (122° F) | |
| Frequency Response | 60 Hz to 13 kHz (+/- 3 dB) | |
| Simultaneous Use | 10 channels per band (maximum recommended) | |
| RECEIVER | ||
| Receiving System | Double conversion super heterodyne | |
| RF Sensitivity | 20 dBuV (at 60 dB S/N ratio, 50 ohms termination) | |
| Headphone Output Connector | 3.5 mm TRS stereo phone jack | |
| Headphone Output Power | 65 mW (at 32 ohms) | |
| Antenna Input | SMA-type, 50 ohms | |
| Aux Input Connector | 3.5 mm TRS stereo phone jack | |
| Batteries | 2 x 1.5V AA | |
| Battery Life | 8 hours (alkaline) | |
| Dimensions | 70.0 mm W x 25.0 mm L x 110.0 mm H | |
| Net Weight | 110 g, without batteries | |
| TRANSMITTER | ||
| RF Power Output | 10 mW/30 mW (switchable internally), 50 ohms. Limited to 10 mW within 863 MHz to 865 MHz | |
| Input Connections | XLRF-type/6.3 mm stereo (1/4") combination connector, Pin 1 and Sleeve-Ground, Pin 2 and Tip-Hot, Pin 3 and Ring-Cold | |
| Maximum Input Level | XLRF-type/6.3 mm stereo, (1/4") balanced +26 dBu, 6.3 mm (1/4") mono, unbalanced +26 dBu | |
| Loop Output Connector | XLRM-type connector, Pin 1-Ground, Pin 2-Hot, Pin 3-Cold | |
| Power Requirement | 12-18V DC, 600 mA | |
| Antenna | Attached whip | |
| Dimensions | 210.0 mm W x 132.0 mm L x 44.0 mm H | |
| Net Weight | 870 g, without accessories | |
See any errors on this page? Let us know.
